VPI Transformer: Working Principle, Advantages and Application Limits

Aug 06, 2025

Leave a message

Working Principle of the Vacuum Pressure Impregnation Process

The acronym VPI stands for vacuum pressure impregnation, and it describes a three-stage treatment of a completed winding. In the drying stage the coil is held under vacuum and at elevated temperature until the moisture content of the conductor film and the insulating tape has been driven down to the level required by the insulation system. In the impregnation stage resin is admitted to the same vessel while the vacuum is still applied, so that resin fills the spaces that the evacuation has emptied. In the pressure stage dry gas or nitrogen is applied above the resin surface, forcing the resin into the remaining cavities before the coil is drained and cured.

What makes the process work is the order of operations. Draining first and then pulling pressure would leave cavities behind; admitting resin under pressure into a winding that still contains air would trap that air instead of removing it. The result is a winding in which the resin, the enamel and the tape form one continuous dielectric, and partial discharge has very few initiation sites left.

Why a Sealed Winding Behaves Differently in Service

Moisture is the main ageing agent for a dry-type winding, and it attacks both the insulation resistance and the discharge behaviour. A varnish-dipped winding has an open surface texture that adsorbs water in humid air; a VPI winding presents a closed resin surface to the atmosphere, so the moisture that reaches the interior must diffuse through the cured matrix rather than along open channels. In practice this is observed as a higher and more stable insulation resistance after a wet period, and as a lower partial discharge reading at the routine test.

The cured resin also stiffens the coil mechanically. Short-circuit forces act to push the outer turns outward and to bend the coil axial length, and a rigid impregnated structure resists that movement with less conductor displacement than a bundle of individually insulated turns. Vibration transmitted from rotating machines or from rail traffic is handled in the same way.

Advantages and Trade-Offs

Characteristic VPI dry-type Oil-immersed
Fire and leakage risk No oil, no bund, no fire separation in most codes Requires oil containment and fire provisions
Overload capability Lower, air cooling limits the hot spot rise Higher, oil circulation carries heat from the winding
Maintenance No oil testing, no oil replacement Periodic oil tests, gasket and breather attention
Installation location Directly in a load centre or on a mezzanine Outdoor compound or dedicated oil room
Routine testing Applied and induced voltage, partial discharge Insulation resistance, turns ratio, oil breakdown
Typical voltage range Medium voltage distribution windings Distribution through transmission levels

The trade-off to weigh honestly is thermal. Air has a low heat transfer coefficient, so the same rating has to be built with more copper and iron or accepted with a shorter overload window. Where the load is steady and the ambient is controlled, that cost is small. Where the duty involves frequent short overloads, the calculation has to be redone against IEC 60076-12 rather than assumed.

Where VPI Transformers Are Specified

The applications share one property: the transformer must live close to the load, often among people. Airports and metro systems use them for traction auxiliary supply and station services, because a liquid-filled unit in a tunnel or a public concourse would require measures that are difficult to maintain. Hospitals specify them for the supply to theatres and life-safety circuits, where a leak or a fire in an oil-filled unit is unacceptable. High-rise buildings use them floor by floor for the same reason. Data centres, industrial drives and process lines use them where the winding has to tolerate dust, humidity and harmonic-rich load without an oil sample programme.

Two conditions should make the designer pause. The first is a very high continuous ambient, such as an unventilated roof space in a hot climate, where the air cooling margin disappears. The second is a location where the enclosure cannot be ventilated at all and the sound limit prevents fans, in which case the de-rating may become uneconomic and another technology should be compared.

Specifying a VPI Transformer

State the rated voltage and insulation level, the rated capacity and impedance, the insulation class, the temperature rise limit, the enclosure protection degree and the ambient range in the enquiry. Ask for the routine test report, including the partial discharge result, for each unit, and for the type test evidence of the insulation system at the temperature class offered. Confirm the conductor material and the winding temperature sensor arrangement, and require the loading guide used for any declared overload to be named, so that the overload figures can be checked against IEC 60076-12 instead of being taken on trust.

Frequently Asked Questions

Q: What does VPI stand for in a transformer?
A: Vacuum Pressure Impregnation. The winding is dried under vacuum, resin is admitted under the same vacuum, and pressure is applied to force the resin into every remaining void before the coil is cured.

Q: Is a VPI transformer the same as a cast resin transformer?
A: No. A cast resin winding is moulded in a resin that becomes the mechanical structure of the coil. A VPI winding is wound with its own insulation build and is then impregnated and cured, so the resin seals the winding rather than forming it.

Q: Why does a VPI transformer have a lower overload rating?
A: Heat is removed by air, which transfers heat far less effectively than circulating oil, so the winding hot spot rises faster at a given current. The permissible overload time should be taken from the dry-type loading guide in IEC 60076-12.

Q: Are fans needed for a VPI transformer?
A: Only where the ambient is high or the enclosure cannot be ventilated naturally. Forced cooling raises the permissible continuous load but adds a moving part that needs maintenance, so many specifications prefer a larger transformer without fans.

Q: How is moisture resistance demonstrated?
A: Through the insulation resistance measured before and after a humidity exposure, and through the partial discharge result at the routine test. A limit of 10 pC is the figure commonly written into medium-voltage specifications.

Q: Can a VPI transformer be used for rectifier or drive duty?
A: Yes, provided the harmonic content and the resulting additional losses are stated in the enquiry, because harmonic currents raise winding eddy losses and the k-factor of the load has to be reflected in the design.

Send Inquiry